The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too.

Should toilet flange be above or below floor?

The optimum flange height to aim for is 1/4 inch above the finished floor. This typically allows for almost any type of wax ring to be used and still ensure a good seal. If you recently tiled or changed the bathroom flooring, the flange height is likely less than optimal.

Do you put vinyl flooring under toilet?

You can put vinyl plank flooring under the vanity, under the toilet, and around the bathtub. … Vinyl planks must go under the toilet to offer support and vinyl planks can be installed around the bathtub with caulking.

Can you install a toilet over vinyl plank flooring?

It’s considered best practice to always put a toilet on top of the flooring, whether the floor is made of wood, vinyl, tiles, etc. Not only will placing the toilet on top of the vinyl plank flooring generally look better, but it also ensures that the weight of the toilet is held by the floor and not the pipes.

Does toilet flange need to be secured to floor?

The flange should be fastened to the floor. Dry fit the toilet to make sure it doesn’t rock. If it does rock, use shims to prevent rocking – just tightening the bolts probably will not stop the rocking but will risk cracking the toilet or breaking the flange.

Where should a toilet flange sit on a finished floor?

5 Answers. The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too.

Does toilet flange go inside or outside pipe?

Install a toilet flange on the outside. This can be done with a hammer and chisel. If the flange is cast iron with a rubber gasket, you should be able to remove the cast iron with a hammer and chisel, remove the rubber gasket with a sharp knife, then replace the gasket and the flange.

Can you tile bathroom floor without removing toilet?

While it is possible to install a new linoleum or ceramic tile floor without removing the toilet, it is not recommended and actually can increase the labor involved in the project. …

Can you fit a toilet on top of laminate flooring?

Because laminate flooring floats above the sub-floor on top of underlayment, it will expand and contract slightly with the temperature and humidity of the room. This makes it impossible for any caulking around the base of the sink and toilet to hold.

Is vinyl flooring OK for bathrooms?

Vinyl is a standout choice for bathroom flooring. There are several different vinyl products, including luxury vinyl tile (LVT) and vinyl roll (also known as sheet vinyl), and both of these are excellent bathroom flooring choices. They’re durable, moisture-resistant, easy to clean and maintain, and warm underfoot.

Article first time published on

How do you secure a toilet flange to a concrete floor?

Use Tapcon anchors or a similar type of masonry/concrete screw to fasten the toilet flange to the concrete slab. If using a plastic flange ring, be careful not to crack the ring by screwing the anchors in too far. With the toilet flange in place, you are ready to install the toilet with a new wax ring.

Why does my toilet rock when I sit?

Toilets usually rock because they are not resting flush against the floor. Underneath the toilet base is a round toilet flange that connects the toilet to the drain pipe. If the flange is a little higher than the surrounding flooring, the toilet becomes raised slightly in the center, allowing it to rock to either side.

Should toilet flange be glued to pipe?

pvc flange should be glued into a pvc pipe. IT would have been less of a problem if a plumber had made the replacement. Use a “good” flange and you will not have to do it again. Caulk is NOT glue.

When should I use toilet flange spacer?

You need a flange extender when the existing flange is too low to hold the wax ring in the correct place to meet the bottom of the toilet drain.

Should toilet flange be flush with subfloor?

It’s easier to get your flange flush with the floor if you first lay your flooring before you install the flange. … Third, you can take off the flange as well as the toilet and trim down the waste pipe that comes up through your bathroom floor. This opening of this pipe should be level and flush with the floor.

How do you secure a toilet to a wood floor?

One you’ve secured the toilet to the flange by tightening the two toilet bolts, protect the wood floor with caulk. Clear or colored silicone caulk are both suitable to caulk the toilet to the floor.

Can you put water resistant laminate flooring in a bathroom?

Pros of Waterproof Laminate Flooring Better with moisture than traditional laminate: Waterproof floors feature a moisture-resistant core so they hold up better to water than traditional laminate or hardwood floors. This means they can be installed in basements, bathrooms, kitchens, and any room throughout the home.

What goes in first flooring or toilet?

Which should be installed first? Typically you’ll want the plumber to install the closet flange (what the toilet bolts onto) at finished floor height. Then install subfloor, underlayment and final floor. Finally you’ll install toilet on top of finished floor.

Do you install flooring before vanity?

Generally, flooring contractors prefer that the cabinets go in first so that there is less possibility of the floor getting scratched. Cabinet installers like the floor to be in place so that the cutting and dust from the floor installation will not damage the vanity.